Most anglers spend hundreds on rods, reels and sounders, then fillet the catch with whatever knife has been rattling around the tackle box since 2011. It's the last step between the water and the plate, and a bad knife loses you flesh, leaves ragged fillets, and turns a ten-minute job into forty.
The truth is there's no single "best" fillet knife. The right one depends on what you catch. This guide explains the three things that matter (length, flex and steel) and how to match them to Australian fish.
1. Length: match the blade to the fish
The simple rule: your blade should be a little longer than the fish is wide, so you can make each cut in one smooth stroke rather than sawing.
- Around 150 to 180mm: small to medium fish. Whiting, bream, flathead, tailor, garfish, squid.
- Around 190 to 200mm: medium to large fish. Snapper, mulloway, salmon, kingfish at smaller sizes.
- 220mm and up: big fish. Tuna, large kingfish, samsonfish, and breaking down loins.
Too short and you're sawing, which tears the flesh. Too long on a small fish and you lose control around the delicate bones.
2. Flex: the most misunderstood part
Flex is how much the blade bends. It's the difference between a fillet knife and any other knife.
- Flexible: bends easily and follows the shape of the backbone and ribs, so you leave less flesh behind. Ideal for small, delicate fish, and for taking skin off.
- Semi-stiff: the all-rounder. Enough backbone to push through larger fish and cut through pin bones, enough flex to work around the frame.
- Stiff: for heavy work on big, dense fish, and for cutting loins and steaks.
A common mistake is buying a very flexible knife for big fish. It wobbles, won't push through, and you end up fighting it.
3. Steel: salt water changes everything
A fillet knife lives in the worst possible environment for steel: salt water, fish slime and wet decks. So corrosion resistance matters as much as sharpness.
We use Sandvik 14C28N, a Swedish stainless steel, for our fillet knives, heat-treated to 58 HRC. It's highly corrosion resistant, takes a very fine edge, and, importantly on a boat, is easy to touch up with a small stone or rod. A super-hard steel that holds an edge for months is no use if you can't bring it back when it goes dull mid-session.
4. The handle: grip when it's wet
Fish are slippery, and so are your hands after the first one. Look for a handle that grips when wet and won't absorb water or fish smell. Our fillet knives use G10, a glass-fibre laminate that's waterproof, tough and textured enough to hold onto.
Our three fillet knives (and which fish they're for)
We built our fillet knife collection around three of Australia's most important fish, each with the length and flex that species needs. All three use 14C28N at 58 HRC, a 50/50 grind and G10 handles.
The King George Whiting ($235)
180mm cutting edge, flexible, 2mm steel. For whiting, bream, flathead, garfish and other smaller, fine-boned fish where every gram of flesh counts. The flex lets it follow the ribcage and take skin off cleanly.
The Snapper ($265)
195mm cutting edge, semi-stiff, 2mm steel. The all-rounder, and the one to buy if you only buy one. Firm enough for snapper's larger frame and thick skin, flexible enough to work around the skull and ribs.
The Blue Tuna ($295)
230mm cutting edge, 2.24mm steel. For tuna, kingfish and other big, dense fish, and for breaking down loins into portions. The extra length means long, uninterrupted cuts.
The whole set
If you fish for everything, the three-piece set ($645) covers you from whiting to tuna.
Looking after a fillet knife
- Rinse in fresh water after every session. Salt left on any steel will eventually find a way in.
- Dry it completely before putting it away, especially if it lives in a sheath.
- Touch up often. A few strokes on a ceramic rod or whetstone before each session keeps it sharp far longer than waiting until it's blunt.
- Keep it for fish. Cutting bait, rope or cable ties on the same knife dulls it fast. That's what a fishing pocket knife is for.
Frequently asked questions
What length fillet knife do I need?
Around 180mm for whiting-sized fish, 195 to 200mm for snapper-sized fish, and 220mm or more for tuna and large kingfish. If you only own one, a semi-stiff knife of around 195mm is the most versatile.
Should a fillet knife be flexible or stiff?
Flexible for small, delicate fish and skinning. Semi-stiff for most medium to large fish. Stiffer blades for big, dense fish and loins.
What's the best steel for a fillet knife?
A highly corrosion-resistant stainless steel that's easy to sharpen, such as Sandvik 14C28N. On a boat, being able to restore the edge quickly matters more than extreme hardness.
Can I use a fillet knife in the kitchen?
Absolutely. A flexible fillet knife is excellent for trimming silverskin from meat and for skinning fish fillets bought from the fishmonger.
Ready to put it to work? Read our step-by-step guide to filleting a snapper, or browse the fillet knife collection.